- To play some more with the armhole: position, fit, ease.
- the original Burda sleeve does not have the grain centered, does this have a function?
- another collar.
PATTERN ALTERATIONS made on the Grey Winter Deer blouse pattern:
- bringing the armhole closer to the body in the front and back. Not taking in sideseam nor altering how it meets the sleeve. (my alterations widen the armhole… or not?)
- shortening the shoulderseam by 2 cm. Doing this at the princess seam point instead of the arm hole. Just to find out.
- taking off the integrated collar, inserting the collar from Deer & Doe instead.
- a little more pronounced shaping at the underbust on the side front panels
- not forgetting the horizontal dart in the front panels this time.
same alterations I made for the Grey Winter Deer when compared to the Stylish Cat Lady Blouse:
- extend the front panel towards the collar, don’t let it bend away so fast
using the front panel -free cut to extend the Center Front seam- for cutting the facings.
not the sleeve seam though. (sleeve cap yes)
NOW CHANGE TO RIGHT COLOUR THREAD.
horizontal one in the front panel and the cup darts at the side.
- sleeve seam
- zipper (new way, just like a lined zipper pouch.)
- long seams
- shoulder seams
2. Zipper sandwiched between front panel and facing. Having it’s end peak out so it’s hidden from the right side:
Precise cutting makes for precise positioning, front panel, zipper and facing line up beautifully:
Because I did the zipper before I sewed the princess lines I could work it like a zippered pouch. I used a tutorial.
3. Princess seams are quite curvy. Here’s one panel laying on top of its partner:
Pin it down, cut into the seam allowance and staystitching to make it work:
– the princess seams ended way too much to the side, they don’t run over the apex.
The zipper is not yet top stitched, that may draw in the princess seams a bit. Topstitch the zipper and see what’s what. Before the topstitching I pressed and pinned the fabric carefully. On the outside it covers the zipper, on the inside it lays back a bit, for easier operating of the zipper.
But somehow, no matter how well you pin and press, the upper layer will wrinkle because the dog teeth make the under layer go faster. There’s a lot of pulling and smoothing involved to make it look acceptable. Slow sewing.
– I need little darts at the side bust, before I put in the sleeves.
Zipper top stitched. Princess seams are still off the apex, 2 cm too much to the sides at least. I think I might have added some width to the front panels when I cut it? Perhaps because I wanted a button band and snap ons buttons. Then I changed it to a zipper but didn’t take out any fabric. Will do for a next time I use this pattern.
For now I think I’ll leave it like this. It was quite an effort to sew the princes seams, with their curves, I don’t look forward to resewing them. And I fear the armhole is already positioned enough towards the bust, it shouldn’t go any nearer.
Taking in the sideseams at the underarm makes up for the surplus of fabric. Took in a whole (2x)1 cm. Now it’s snug. Might be too snug.
The curve at the underbust -more curvy than the previous blouse- works well. But still horizontal folds.
I wonder if they’d be less if the closing CF was not as stiff as a zipper is.
Sewing in side darts.
pinned one and sewed it in with sleeve running close to the dog teeth and bodice on top. No trouble easing it in.
Fitting showed I had not enough room at the front. I’m going to take out the bust dart.
(sleeve cap seems to be too roomy at the front but this is the 2 cm seam allowance bulking things up. It’s not been graded yet.)
Shoulder seam is positioned a bit to the back:
(the collar is going to need some serious engineering. I know nothing about collars! Yet.)
took out the bust dart. While sewing the arm hole was now too big for the sleeve. As the shoulder seam was a bit too much to the back I took it apart and used it to take away some of the excess fabric of the armhole. (we’re talking maybe one cm here, exactly how much the side bust dart took up.)
looks awful. Sits even worse.
It looks like I moved the shoulder seam to the back instead of the front (??)
The arm hole is way too wide at the front top, the sleeve cap is too narrow over my upper arm. I can’t move one bit, it looks like I sewed a sloper, with no ease.
The whole arm hole sits awful. It should be nearer to my body. Higher in the sideseam, closer to the body in the front. The shoulder seam should even be shorter I think, but then the sleeve will move on top of my shoulder and that’s not good.
But the extra ease from the abandoned bust dart is good though. It’s on the right side in this picture:
Blouse thrown in corner. I’m done sewing for the day.
HOW TO PROCEED:
got no idea. The sleeves have to come off, that’s clear. I have enough fabric to draft new sleeves. But how? What?
Take the bodice -with bust darts- as a point of departure I guess. That one sits good and looks fine. But the arm hole is a bit wide at the front. How attach a sleeve to it without it becoming wings?
Maybe a gusset at the underarm…
The bustdarts do give the armhole a right angle. It’s no longer oblong.
The sleeves need some sort of wearing ease, at the sleeve cap. Even though Fashion-Incubator makes a good case that it’s nonsense.
Drape the sleeve in the hole?
I think I shouldn’t have matched up the seam of the sleeve with the side seam. Fashion-Incubator shows a rotated sleeve in her last picture.
I’m also thinking about sewing it in back side to front, just to see if that changes anything.
NEXT TIME I use this pattern:
– broaden the side front panels: make the arm hole smaller by bringing it closer to the arm pit. It’s about 2 to 4 cm out.
– more soupleness at the closing (CF) to see if the horizontal wrinkles at the underbust disappear. That rules out a zipper.