Failed: Lila Dress Shirt

Based on Beige Beestjes Shirt I made a new pattern, with princess seams for better shaping at the underbust and looking for a better armhole. I sewed the shirt but the fit is so bad I won’t finish it.
fitting of handsewn self drafted blouse (it doesn't fit well. Too much shaping in too few princess seams. Also needs more wearing ease and lower armhole.)fitting of handsewn self drafted blouse (it doesn't fit well. Too much shaping in too few princess seams. Also needs more wearing ease and lower armhole.) fitting of handsewn self drafted blouse (it doesn't fit well. Too much shaping in too few princess seams. Also needs more wearing ease and lower armhole.)fitting of handsewn self drafted blouse (it doesn't fit well. Too much shaping in too few princess seams. Also needs more wearing ease and lower armhole.)fitting of handsewn self drafted blouse (it doesn't fit well. Too much shaping in too few princess seams. Also needs more wearing ease and lower armhole.)

The main problems are the armholes and that the shaping at the underbust is too extreme for the fabric. This petite busty woman needs more than two princess seams at the front. Right now the shaping on those two is too extreme and the fabric stretches and flares.

I did bring the Beige Beestjes Shirt up to a pattern with princess seams, both in the front and the back. Back is nearly good now, it just needs a little less curves at the bottom. (It’s not too tight at the arm hole, the tightness there is caused by the armhole and sleeve. But it looks weird, I agree.)

It’s getting better and better though. Combining this with “Loes’ bloes” from the previous post and I’ll have something wearable soon.

Process for Lila Shirt:
using Block April 2016, to find out if it’s ok. Basically a resew of the slippery cheap market cotton shirt from June 2016 that was a failure.

  • amendments: using “upperbust” (=93 cm) at the point that this pattern drafting methode uses “borstwijdte” which is right at the horizontal line at the armpits. This brings in the sideseam at that point, by 4×2 cm for the block. At the apex (nipples) I’m still using “borstwijdte”. Basically I’ve now used my upperbust and given the block a FBA. I found that each shirt drafted from the block was too wide at the armpit, just where I wanted the armhole to be fitted.
  • amendments: elongating shoulder seam by 1 cm
  • new shirt pattern from the block will have princess lines both front and back and a new sleeve and arm hole, derived from Beige Winterbeestjes bloes. I mainly need this block for better waist shaping (and the mentioned snugness at the arm pit horizontal line).
  • amend block to have a CB that’s not straight? Has the waist shaping incorporated instead? –> only whenever there’s a CB seam. Otherwise use two princess seams.

Still working towards the ultimate Dress Shirt Pattern for all my future shirts and any woven that catches my fancy. From Block to Pattern:

  • swiffel side bust dart to the waist dart, not to the armhole.
  • match front and back panel at the shoulder seams and make arm hole nice and round at the top.
  • 1 cm wearing ease at the side seam/arm pit
  • back shoulder side dart swivveled to shoulder seam (will become part of princess seam, no yoke this time). Not sure if the line is supposed to be at a square angle with the shoulder seam. I just assume so. Next: redraw the arm hole so it’s smooth again.
  • draw princess seam. Will smoothen
  • add wearing ease: 1 to 1,5 cm at the sideseam. Compare with pattern for Beige Winterbeestjes
  • neck CB -0,5 cm; shoulder seam -1,5 cm. Bottom CB + 3 cm, sideseam -2 cm
  • SA 1,5cm
  • frontpanel: swivveled side BD close and brought it to the waist dart. Swivveled arm hole BD to the princess seam in the shoulder. Left with an akward arm hole. Smoothened it and now have a front length of the arm hole of 19,1 cm. The length of the front of the sleeve cap is 22,9. I’ll never be able to ease that in, too much difference. (the original, awkward arm hole is 19,1 cm). I’ve folded away some of the width of the sleeve, with the emphasize on the sleeve cap. Front of that is now 22,1 cm wide, the back 24,0. That’s 4 cm more than the armhole. I’m going to try and ease it in. I think 3 is the maximum you’re supposed to do but if need be I can resort to a fold at the high point of the sleeve. I’ve drawn the line a little closer to the original awkward armhole, another few mm won. Also: I had widened the sleeve at the biceps with 2,5 cm. Half of that has now been folded away. I will do another sleeve adjustment to get that back. The shape of the sleeve cap will flatten even more as a result.
  • 2,5 cm van de mouw af voor een mouwlengte van 59 cm. Machet is 13 cm hoog, dubbelgevouwen, met manchetknopen. Nagetekend van mijnwitte bloes.

backpanel: dart to princes seam:

pattern drafting Lila Dress Shirt bust darts

front panel: closing side dart. Making a princes seam to the arm hole results in terrible angled side panel (see pencil-finger-pencil). I opt for princes seam to the shoulder seam. pattern drafting Lila Dress Shirt bust dartspattern drafting shirt Sewing darts armhole

that weird steep armhole again… rounding it off. Butn ow the circumference gets too out of line with the length of the sleeve cap. Settling on the middle line. pattern drafting shirt Sewing darts armholepattern drafting shirt Sewing darts armhole

I made some adjustments to the block, based on this shirt. One of them is lowering the shoulderseam at the neck by 1 cm:

fitting of handsewn self drafted blouse (it doesn't fit well. Too much shaping in too few princess seams. Also needs more wearing ease and lower armhole.)

The main problem, other than the armhole, is that the extreme waist shaping a busty petite woman needs cannot be done in just two princess seams.
fitting of handsewn self drafted blouse (it doesn't fit well. Too much shaping in too few princess seams. Also needs more wearing ease and lower armhole.)fitting of handsewn self drafted blouse (it doesn't fit well. Too much shaping in too few princess seams. Also needs more wearing ease and lower armhole.)fitting of handsewn self drafted blouse (it doesn't fit well. Too much shaping in too few princess seams. Also needs more wearing ease and lower armhole.)

I’m looking at designs with more seams, more panels, horizontal parts even.

Like these from DD-atelier and CarrisaRose: